Lockwood 202 Exterior Round Corner Plate - Flush Pull & Privacy Indicating Emergency Turn | Satin Stainless Steel
The Lockwood 202 Series Exterior Plate with Flush Pull and Privacy Indicating Emergency Turn is part of the distinguished Artefact range of round corner plate door furniture - designed, assembled and customised in Australia for the Australian market. This exterior plate configuration combines a recessed flush pull with a privacy indicating emergency turn, providing a low-profile pull function alongside occupied/vacant indication for privacy rooms such as accessible bathrooms, ensuites and amenity facilities.
The recessed flush pull sits flush with the plate face, making this configuration ideal for sliding doors and cavity sliders where a projecting pull handle would obstruct the door recess or frame, as well as hinged doors where a minimal exterior profile is preferred. The privacy indicating emergency turn displays the room's occupied or vacant status from the outside, and incorporates an emergency release allowing entry from the exterior in an emergency without damaging the furniture.
The 202 Series features the same 162 x 162mm plate profile as the 200 Series but with 10mm radius corners. Compatible with Lockwood Synergy 3570 and Selector 3770 Series Mortice Locks, latches, and push/pull doors. Supplied in Satin Stainless Steel in both left and right hand.
Usually ships in 11 business days
This product is a special order item and cannot be returned. Please confirm handing and suitability before ordering.
Finish
Satin Stainless Steel
SS
Available in left and right hand. Single finish option for this configuration.
Fire Rated
- Fire rated up to 2 hours in accordance with AS1905.1:2005 (Fire Resistant Doorsets).
- Fire performance is dependent on doorset type and configuration.
- Fire compliance is system-based and limited by the Fire Resistance Level of the complete doorset assembly.
Key Features
- Round corner 162 x 162mm exterior plate with 10mm radius corners - Lockwood Artefact 202 Series
- Flush Pull and Privacy Indicating Emergency Turn configuration (Function 35)
- Recessed flush pull - no projecting handle, low-profile exterior face
- Privacy indicating emergency turn - displays occupied/vacant status from the exterior
- Emergency release function - allows outside entry in an emergency without damaging the furniture
- Concealed fixings - clean exterior face with no visible screws
- Available in left and right hand
- Suitable for sliding doors, cavity sliders and hinged doors
- Slim-line profile suited to public, commercial, industrial and institutional buildings
- Designed, assembled and customised in Australia for the Australian market
- Tested to Level D8 (500,000 cycles) - AS4145.2-2008
- Fire rated up to 2 hours - AS1905.1:2005
- Pairs back-to-back with the 203 Series interior plate (round corner)
- Compatible with Lockwood Synergy 3570 and Selector 3770 Series Mortice Locks, latches and push/pull doors
- 25-year mechanical warranty
Suitable Uses
- Sliding doors and cavity sliders to accessible bathrooms, ensuites and amenity rooms
- Hinged privacy doors where a flush, low-profile exterior pull is preferred
- Any privacy room requiring occupied/vacant indication and emergency access from the outside
- Aged care, healthcare, education and hospitality facilities
- Fire-rated door assemblies (when paired with a rated Lockwood mortice lock)
- Architecturally specified projects requiring a round corner plate profile with minimal exterior projection
Full Specifications
Item Codes
Dimensions & Technical Drawings
Helpful Tips
- Exterior plate - pairs with 203 Series: This is the outside face plate. It must be paired with a 203 Series interior plate (round corner) - not a 201 Series (square corner).
- Flush pull vs P1 pull handle: This plate uses a recessed flush pull (Function 35) with no projection from the plate face. If a projecting stainless steel pull handle is preferred, refer to the P1 pull handle variant (20228NN/P1).
- Sliding door suitability: The flush pull makes this plate particularly well suited to sliding and cavity slider doors where a projecting handle would obstruct the door recess or pocket.
- Flush pull back to back: Minimum door thickness is 40mm when using flush pulls back to back.
- How the privacy indicator works: When the occupant engages the inside turn snib, the indicator on this exterior plate changes to show the room is occupied. When released it returns to vacant.
- Emergency release: The exterior plate incorporates an emergency release - the door can be opened from outside using a coin, flat tool or dedicated release key without damaging the furniture.
- Concealed fixings: This plate uses concealed fixing studs. The paired interior 203 plate must use visible fixings - confirm pairing before ordering.
- 202 vs 200 Series: The 202 Series has 10mm radius round corners. If square corners are required, refer to the 200 Series equivalent.
- Handing: Determined by which side the hinges are on when facing the door from outside. Left hand = hinges on the left.
- Thick doors: For doors 45-55mm, order long fixing screws SP2000-208 separately.
- Non-returnable: This item cannot be returned once ordered - confirm handing and suitability before purchasing.
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
- Mechanical components: 25 years
- Electrical and electronic components: 2 years (excluding batteries)
- Everbrass: 25 years
- Stainless Steel, Chrome & Anodised: Up to 10 years
- PVD / VIVID: 10 years
- Symmetry: 5 years
- Decorative finishes (Bronze, Antique, Powdercoat): Typically 2 years
Lockwood 200/202 Series Handle Catalogue
Lockwood Warranty Overview
Lockwood branded products are covered by manufacturer warranties issued by ASSA ABLOY Australia Pty Ltd. Warranty periods vary depending on product type, mechanical components, electrical elements, and finish category.
This overview summarises the structure of Lockwood warranty coverage. Full terms, exclusions and claim procedures are set out in the official Lockwood Warranty document.
Warranty Periods Summary
Finish Coverage Guide
- Everbrass finishes: up to 25 years against corrosion, tarnishing and discolouration.
- Stainless steel, polished stainless steel, chrome plating and anodised finishes: typically up to 10 years.
- Decorative finishes including Antique Copper, Architectural Bronze, Oil Rubbed Bronze, Aged Brass, Polished Brass, Satin Brass and related variants: typically up to 2 years against corrosion.
- Unlacquered brass finishes will naturally age and change appearance over time. This is not considered a defect.
- Tea staining of stainless steel is not covered where cleaning and maintenance have not been followed.
What the Warranty Covers
- Defects in material and workmanship during the applicable warranty period.
- Assessment by ASSA ABLOY to determine repair, replacement with the same or closest equivalent product, or refund of purchase price.
Common Exclusions
- Normal wear and tear.
- Misuse, abuse, accidental damage or use outside published specifications.
- Improper maintenance or failure to follow care instructions.
- Unauthorised modification, repair or use of non-genuine parts.
- Exposure to corrosive environments including coastal air, salt spray, chemicals or pollution.
- Removal, refitment or associated labour charges.
- Products not originally sold in Australia through authorised channels.
Warranty Claim Process
- Retain proof of original purchase.
- Return the product through the original place of purchase where applicable.
- If claiming directly, obtain a case number before returning goods.
- Products must be securely packed and clearly identified.
- Warranty assessment determines repair, replacement or refund.
Australian Consumer Law
Lockwood warranties operate in addition to rights available under the Australian Consumer Law. Goods come with guarantees that cannot be excluded. Customers may be entitled to a replacement or refund for a major failure and compensation for reasonably foreseeable loss or damage.
Where a product fails to meet acceptable quality standards and the failure does not amount to a major failure, the customer is entitled to repair or replacement.
