Lockwood 202 Exterior Round Corner Plate - Cylinder & Horizontal P1 Pull Handle | Artefact Series
The Lockwood 202 Series Exterior Plate with Cylinder and Horizontal P1 Pull Handle is part of the distinguished Artefact range of round corner plate door furniture - designed, assembled and customised in Australia for the Australian market. This exterior plate configuration combines a horizontal P1 stainless steel pull handle with a Lockwood 570 Series oval cylinder hole, providing keyed entry access alongside a pull handle specifically oriented for sliding and cavity slider doors.
The horizontal pull handle orientation (HP1) positions the handle bar parallel to the door edge, matching the natural lateral pulling motion used when operating a sliding door. This makes the plate the correct choice wherever a cylinder-controlled sliding door is required - such as sliding entry doors, large-format cavity sliders and suspended sliding systems in commercial and institutional buildings. The cylinder must be ordered separately as it is not included with this plate.
The 202 Series features the same 162 x 162mm plate profile as the 200 Series but with 10mm radius corners. The plate pairs back-to-back with the 203 Series interior plate (round corner) and is compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches and push/pull doors. Supplied in Satin Stainless Steel in both left and right hand.
Usually ships in 11 business days
This product is a special order item and cannot be returned. Please confirm handing, door type and cylinder compatibility before ordering.
Finish
Satin Stainless Steel
SS
Available in left and right hand. Single finish option for this configuration.
Fire Rated
- Tested up to 2 hours with a fire rated Lockwood mortice lock on fire door assemblies in accordance with AS1905.1:2005 (Fire Resistant Doorsets).
- Fire performance is dependent on doorset type and configuration.
- Fire compliance is system-based and limited by the Fire Resistance Level of the complete doorset assembly.
Key Features
- Round corner 162 x 162mm exterior plate with 10mm radius corners - Lockwood Artefact 202 Series
- Pull Handle and Cylinder configuration (Function 25) with horizontal pull handle orientation
- Horizontal P1 stainless steel pull handle (HP1) - oriented for lateral sliding door operation
- Accepts Lockwood 570 Series oval cylinder - 32mm (H) x 18mm (W) - cylinder not included, order separately
- Concealed fixings - clean exterior face with no visible screws
- Available in left and right hand
- Specifically suited to sliding doors and cavity slider systems
- Designed, assembled and customised in Australia for the Australian market
- Tested to Level D8 (500,000 cycles) - AS4145.2-2008
- Fire rated up to 2 hours - AS1905.1:2005
- Pairs back-to-back with the 203 Series interior plate (round corner)
- Compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches and push/pull doors
- 25-year mechanical warranty
Suitable Uses
- Sliding entry doors requiring keyed access from the exterior
- Cavity slider doors in commercial, residential and institutional buildings
- Large-format and suspended sliding door systems where lateral pull operation is required
- Office, retail, hospitality and public building sliding entry and internal doors
- Fire-rated sliding door assemblies (when paired with a rated Lockwood mortice lock)
- Architecturally specified projects requiring a round corner plate profile in stainless steel
Full Specifications
Item Codes
Dimensions & Technical Drawings
Helpful Tips
- Horizontal vs vertical pull handle: This plate uses the HP1 horizontal pull handle, oriented parallel to the door edge for lateral sliding door operation. If a vertical pull handle is required on a hinged door, refer to the standard vertical P1 variant (item code prefix 20225NA/P1).
- Cylinder not included: This plate accepts a Lockwood 570 Series oval cylinder (32mm H x 18mm W) but the cylinder is not supplied - order it separately to suit your key system.
- Confirm mortice lock compatibility for sliding doors: Not all Lockwood mortice locks are suited to sliding door applications. Confirm that the lock you are pairing with this plate is rated and approved for sliding or cavity slider use.
- Exterior plate - pairs with 203 Series: This is the outside face plate. It must be paired with a 203 Series interior plate (round corner) - not a 201 Series (square corner).
- Concealed fixings: This plate uses concealed fixing studs. The paired interior 203 plate must use visible fixings - confirm this when ordering the interior plate.
- Handing: Determined by which side the hinges or pivot point are on when facing the door from outside. Left hand = hinges/pivot on the left.
- 202 vs 200 Series: The 202 Series has 10mm radius round corners. If square corners are required, refer to the equivalent 200 Series plate.
- Thick doors: For doors 45-55mm, order long fixing screws SP2000-208 separately.
- Non-returnable: This item cannot be returned once ordered - confirm handle orientation, handing and cylinder compatibility before purchasing.
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
- Mechanical components: 25 years
- Electrical and electronic components: 2 years (excluding batteries)
- Everbrass: 25 years
- Stainless Steel, Chrome & Anodised: Up to 10 years
- PVD / VIVID: 10 years
- Symmetry: 5 years
- Decorative finishes (Bronze, Antique, Powdercoat): Typically 2 years
Lockwood 200/202 Series Handle Catalogue
Lockwood Warranty Overview
Lockwood branded products are covered by manufacturer warranties issued by ASSA ABLOY Australia Pty Ltd. Warranty periods vary depending on product type, mechanical components, electrical elements, and finish category.
This overview summarises the structure of Lockwood warranty coverage. Full terms, exclusions and claim procedures are set out in the official Lockwood Warranty document.
Warranty Periods Summary
Finish Coverage Guide
- Everbrass finishes: up to 25 years against corrosion, tarnishing and discolouration.
- Stainless steel, polished stainless steel, chrome plating and anodised finishes: typically up to 10 years.
- Decorative finishes including Antique Copper, Architectural Bronze, Oil Rubbed Bronze, Aged Brass, Polished Brass, Satin Brass and related variants: typically up to 2 years against corrosion.
- Unlacquered brass finishes will naturally age and change appearance over time. This is not considered a defect.
- Tea staining of stainless steel is not covered where cleaning and maintenance have not been followed.
What the Warranty Covers
- Defects in material and workmanship during the applicable warranty period.
- Assessment by ASSA ABLOY to determine repair, replacement with the same or closest equivalent product, or refund of purchase price.
Common Exclusions
- Normal wear and tear.
- Misuse, abuse, accidental damage or use outside published specifications.
- Improper maintenance or failure to follow care instructions.
- Unauthorised modification, repair or use of non-genuine parts.
- Exposure to corrosive environments including coastal air, salt spray, chemicals or pollution.
- Removal, refitment or associated labour charges.
- Products not originally sold in Australia through authorised channels.
Warranty Claim Process
- Retain proof of original purchase.
- Return the product through the original place of purchase where applicable.
- If claiming directly, obtain a case number before returning goods.
- Products must be securely packed and clearly identified.
- Warranty assessment determines repair, replacement or refund.
Australian Consumer Law
Lockwood warranties operate in addition to rights available under the Australian Consumer Law. Goods come with guarantees that cannot be excluded. Customers may be entitled to a replacement or refund for a major failure and compensation for reasonably foreseeable loss or damage.
Where a product fails to meet acceptable quality standards and the failure does not amount to a major failure, the customer is entitled to repair or replacement.
