Lockwood 202 Exterior Round Corner Plate - Dual Cylinder & P1 Pull Handle | Artefact Series
The Lockwood 202 Series Exterior Plate with Dual Cylinder and P1 Pull Handle is part of the distinguished Artefact range of round corner plate door furniture - designed, assembled and customised in Australia for the Australian market. This exterior plate configuration features two Lockwood 570 Series oval cylinder holes combined with a P1 stainless steel pull handle, providing a dual-cylinder security solution for high-security commercial and institutional entry doors.
The dual-cylinder arrangement is designed for use with a dual-cylinder mortice lock, where keyed operation is required at two points on the door - typically for deadbolt and latch control independently, or for high-security applications requiring two separate key-operated bolts. Both cylinders must be ordered separately as they are not included with this plate. The plate pairs back-to-back with the 203 Series interior plate (round corner) and is compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches, and push/pull doors.
The 202 Series features the same 162 x 162mm plate profile as the 200 Series but with 10mm radius corners. Supplied in Satin Stainless Steel in both left and right hand.
Usually ships in 11 business days
This product is a special order item and cannot be returned. Please confirm handing, cylinder compatibility and lock suitability before ordering.
Finish
Satin Stainless Steel
SS
Available in left and right hand. Single finish option for this configuration.
Fire Rated
- Tested up to 2 hours with a fire rated Lockwood mortice lock on fire door assemblies in accordance with AS1905.1:2005 (Fire Resistant Doorsets).
- Fire performance is dependent on doorset type and configuration.
- Fire compliance is system-based and limited by the Fire Resistance Level of the complete doorset assembly.
Key Features
- Round corner 162 x 162mm exterior plate with 10mm radius corners - Lockwood Artefact 202 Series
- Pull Handle and Dual Cylinder configuration (Function 30)
- P1 stainless steel pull handle on exterior face
- Two Lockwood 570 Series oval cylinder holes - 32mm (H) x 18mm (W) each
- Cylinders not included - both must be ordered separately to suit your key system
- Concealed fixings - clean exterior face with no visible screws
- Available in left and right hand
- Designed for high-security dual-cylinder mortice lock applications
- Designed, assembled and customised in Australia for the Australian market
- Tested to Level D8 (500,000 cycles) - AS4145.2-2008
- Fire rated up to 2 hours - AS1905.1:2005
- Pairs back-to-back with the 203 Series interior plate (round corner)
- Compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches and push/pull doors
- 25-year mechanical warranty
Suitable Uses
- High-security commercial and institutional entry doors requiring dual-cylinder keyed access
- Doors where independent keyed control of both deadbolt and latch is required
- Restricted access doors in government, defence, healthcare and secure facility buildings
- Fire-rated door assemblies (when paired with a rated Lockwood mortice lock)
- Architecturally specified projects requiring a round corner plate profile in stainless steel
Full Specifications
Item Codes
Dimensions & Technical Drawings
Helpful Tips
- Cylinders not included: This plate has two Lockwood 570 Series oval cylinder holes but neither cylinder is supplied. Both must be ordered separately to suit your key system.
- Confirm dual-cylinder lock compatibility: This plate is designed for use with a dual-cylinder mortice lock. Confirm the Lockwood mortice lock you are pairing this with supports the dual-cylinder function before ordering.
- Important egress safety note: Dual-cylinder configurations require a key to operate from both sides of the door. This arrangement must not be used on fire escape routes or doors required for emergency egress without an approved key override or thumb-turn cylinder solution. Consult your building certifier or fire engineer if in doubt.
- Exterior plate - pairs with 203 Series: This is the outside face plate. It must be paired with a 203 Series interior plate (round corner) - not a 201 Series (square corner).
- Concealed fixings: This plate uses concealed fixing studs. The paired interior 203 plate must use visible fixings - confirm this when ordering the interior plate.
- Handing: Determined by which side the hinges are on when facing the door from outside. Left hand = hinges on the left.
- 202 vs 200 Series: The 202 Series has 10mm radius round corners. If square corners are required, refer to the equivalent 200 Series plate.
- Thick doors: For doors 45-55mm, order long fixing screws SP2000-208 separately.
- Non-returnable: This item cannot be returned once ordered - confirm handing, lock compatibility and cylinder selection before purchasing.
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
- Mechanical components: 25 years
- Electrical and electronic components: 2 years (excluding batteries)
- Everbrass: 25 years
- Stainless Steel, Chrome & Anodised: Up to 10 years
- PVD / VIVID: 10 years
- Symmetry: 5 years
- Decorative finishes (Bronze, Antique, Powdercoat): Typically 2 years
Lockwood 200/202 Series Handle Catalogue
Lockwood Warranty
Lockwood branded products are covered by manufacturer warranties issued by ASSA ABLOY Australia Pty Ltd. Warranty periods vary by product type, with separate cover for mechanical components, electrical and electronic parts, keys, and finishes.
The summary below sets out the standard warranty structure. All warranty claims are handled by Terry's Tradies Pty Ltd and its associated websites, trading names, and subsidiaries. Full terms and exclusions are set out in the official Lockwood warranty document linked at the base of this page.
Warranty Summary
Finish Coverage Guide
- Everbrass finishes: up to 25 years against corrosion, tarnishing and discolouration.
- Stainless steel, polished stainless steel, chrome plating and anodised finishes: typically up to 10 years.
- PVD and VIVID finishes: typically up to 10 years.
- Symmetry range finishes: typically up to 5 years.
- Decorative finishes (Antique Copper, Architectural Bronze, Oil Rubbed Bronze, Aged Brass, Polished Brass, Satin Brass and related variants): typically up to 2 years against corrosion.
- Unlacquered brass finishes naturally age and change appearance over time. This is not considered a defect.
- Tea staining of stainless steel is not covered where the required cleaning and maintenance have not been followed.
How to Make a Claim
- Contact Terry's Tradies Pty Ltd and its associated websites, trading names, and subsidiaries with your proof of original purchase.
- Keep the product securely packed and clearly identified, ready for assessment.
- Where a claim is escalated to the manufacturer, ASSA ABLOY may issue a case number before goods are returned.
- ASSA ABLOY assesses the claim and determines repair, replacement with the same or closest equivalent product, or refund of the purchase price.
Exclusions
- Normal wear and tear.
- Misuse, abuse, accidental damage or use outside published specifications.
- Improper maintenance or failure to follow care instructions.
- Unauthorised modification, repair or use of non-genuine parts.
- Exposure to corrosive environments including coastal air, salt spray, chemicals or pollution.
- Removal, refitment or associated labour charges.
- Products not originally sold in Australia through authorised channels.
These manufacturer warranties apply in addition to your rights under the Australian Consumer Law. Our goods come with guarantees that cannot be excluded under the ACL. You are entitled to a replacement or refund for a major failure and to compensation for any other reasonably foreseeable loss or damage. Where a failure does not amount to a major failure, you are entitled to have the goods repaired or replaced.
