Lockwood EXI296-SIL Exidor Reversible Panic Latch Silver
The Lockwood EXI296-SIL Exidor Reversible Panic Latch Silver is a surface mounted panic exit device designed for emergency egress on suitable single and double door applications. It is part of the Lockwood Exidor series and provides single point latching with push bar operation from the inside.
The EXI296-SIL is operated by a downward thrust of the cross bar, allowing the door to open quickly in an emergency. It is commonly used where a single point panic latch is preferred over a vertical rod panic bolt arrangement.
This model is supplied in Silver finish and is listed as the REV PANIC LATCH LH (STD) Silver. The product is described as reversible in the supplied data, so handing should always be checked against the actual door configuration and installation instructions before fitting.
Key Features
- Push bar activated panic latch for emergency exit operation
- Single point latching for suitable single and double door applications
- Surface mounted design for practical installation and maintenance
- Reversible configuration for flexible door handing requirements
- Fire rated for use on timber and steel door assemblies where correctly specified
- Designed for applications where a panic latch is preferred over top and bottom shoot bolts
- Tested to 200,000 operating cycles for long-term mechanical performance
- Silver finish supplied as standard for this item code
Suitable Uses
- Single door emergency exit applications
- Selected double door applications where a single point panic latch is specified
- Commercial and public access buildings requiring panic exit hardware
- Timber and steel fire door assemblies where the complete assembly is approved
- Industrial, education, healthcare, retail and back-of-house exit doors
- Commonly specified in Australian commercial and industrial sites
Full Specifications
Fire Rated
- Supplied product information states a fire rating of up to 2 hours.
- Successfully tested on fire door assemblies in accordance with Australian Standard AS1905.1-2015 for fire resistant doorsets.
- Fire rated for use on timber and steel doors where the complete fire door assembly is correctly specified and installed.
- Fire door suitability depends on the complete approved door assembly, including door type, frame, fixings, hardware and installation method.
Certifications and Compliance
- Conforms to the standards set out in CE EN1125-2008 according to supplied product information.
- Designed for panic exit applications where people may need to exit quickly during an emergency.
- Correct compliance depends on the complete building, door and escape route specification.
Frequently Asked Questions
Is the EXI296-SIL a bolt or a latch?
The EXI296-SIL is a panic latch, not a vertical rod panic bolt. It provides single point latching and is suited where a latch style panic device is specified.
Can this be used on fire doors?
Yes, supplied product information states fire rating up to 2 hours and fire door testing to Australian Standard AS1905.1-2015. The complete fire door assembly must still be correctly approved and installed.
Is the external lever trim included?
No. External lever trim is an accessory and must be ordered separately where outside access is required. A suitable Euro profile half cylinder is also required for that trim and is not supplied as part of the panic latch.
Additional Information
- The EXI296-SIL is commonly chosen where a single point panic latch is preferred instead of a two point vertical rod panic bolt.
- A common specification mistake is choosing a panic latch when the door set requires top and bottom bolt engagement for the intended security or door configuration.
- Door handing and latch orientation should be checked against the installation instructions before fitting, especially where the product title references left hand standard configuration.
- External access from the outside requires a compatible outside access device and cylinder arrangement. These should be matched to the site keying schedule.
- For fire door applications, through fixings or other project-specific fixing requirements may be needed depending on the door manufacturer and fire test approval.
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
- Mechanical components: 25 years
- Electrical and electronic components: 2 years (excluding batteries)
Lockwood Panic Exit Devices Catalogue
Lockwood Panic Exit Devices Catalogue
Lockwood Warranty Overview
Lockwood branded products are covered by manufacturer warranties issued by ASSA ABLOY Australia Pty Ltd. Warranty periods vary depending on product type, mechanical components, electrical elements, and finish category.
This overview summarises the structure of Lockwood warranty coverage. Full terms, exclusions and claim procedures are set out in the official Lockwood Warranty document.
Warranty Periods Summary
Finish Coverage Guide
- Everbrass finishes: up to 25 years against corrosion, tarnishing and discolouration.
- Stainless steel, polished stainless steel, chrome plating and anodised finishes: typically up to 10 years.
- Decorative finishes including Antique Copper, Architectural Bronze, Oil Rubbed Bronze, Aged Brass, Polished Brass, Satin Brass and related variants: typically up to 2 years against corrosion.
- Unlacquered brass finishes will naturally age and change appearance over time. This is not considered a defect.
- Tea staining of stainless steel is not covered where cleaning and maintenance have not been followed.
What the Warranty Covers
- Defects in material and workmanship during the applicable warranty period.
- Assessment by ASSA ABLOY to determine repair, replacement with the same or closest equivalent product, or refund of purchase price.
Common Exclusions
- Normal wear and tear.
- Misuse, abuse, accidental damage or use outside published specifications.
- Improper maintenance or failure to follow care instructions.
- Unauthorised modification, repair or use of non-genuine parts.
- Exposure to corrosive environments including coastal air, salt spray, chemicals or pollution.
- Removal, refitment or associated labour charges.
- Products not originally sold in Australia through authorised channels.
Warranty Claim Process
- Retain proof of original purchase.
- Return the product through the original place of purchase where applicable.
- If claiming directly, obtain a case number before returning goods.
- Products must be securely packed and clearly identified.
- Warranty assessment determines repair, replacement or refund.
Australian Consumer Law
Lockwood warranties operate in addition to rights available under the Australian Consumer Law. Goods come with guarantees that cannot be excluded. Customers may be entitled to a replacement or refund for a major failure and compensation for reasonably foreseeable loss or damage.
Where a product fails to meet acceptable quality standards and the failure does not amount to a major failure, the customer is entitled to repair or replacement.
