Lockwood 202 Exterior Round Corner Plate - Pull Engraving & P1 Pull Handle | Satin Stainless Steel
The Lockwood 202 Series Exterior Plate with Pull Engraving and P1 Pull Handle is part of the distinguished Artefact range of round corner plate door furniture - designed, assembled and customised in Australia for the Australian market. This exterior plate features a full solid infill "PULL" text engraving alongside a P1 stainless steel pull handle, providing clear directional instruction for building occupants on the pull side of push/pull doors.
With no cylinder or turn snib, this plate is designed purely for pass doors and push/pull door applications in commercial, retail, hospitality and public-access environments where keyed access is not required on the exterior face. The full solid infill engraving (black gloss standard) provides strong, legible wayfinding that suits high-traffic settings. This plate pairs back-to-back with the 203 Series interior plate (round corner) and is compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches and push/pull doors.
The 202 Series features the same 162 x 162mm plate profile as the 200 Series but with 10mm radius corners, giving a softer, contemporary aesthetic. Supplied in Satin Stainless Steel in both left and right hand.
Usually ships in 11 business days
This product is a special order item and cannot be returned. Please confirm handing and suitability before ordering.
Finish
Satin Stainless Steel
SS
Available in left and right hand. Single finish option for this configuration.
Fire Rated
- Tested up to 2 hours with a fire rated Lockwood mortice lock on fire door assemblies in accordance with AS1905.1:2005 (Fire Resistant Doorsets).
- Fire performance is dependent on doorset type and configuration.
- Fire compliance is system-based and limited by the Fire Resistance Level of the complete doorset assembly.
Key Features
- Round corner 162 x 162mm exterior plate with 10mm radius corners - Lockwood Artefact 202 Series
- Pull Handle Only configuration (Function 24) with full solid infill "PULL" text engraving
- P1 stainless steel pull handle on exterior face
- Full solid infill engraving - black gloss standard - high visibility wayfinding for high-traffic doors
- No cylinder or turn snib - pull-only exterior plate
- Concealed fixings - clean exterior face with no visible screws
- Available in left and right hand
- Designed, assembled and customised in Australia for the Australian market
- Tested to Level D8 (500,000 cycles) - AS4145.2-2008
- Fire rated up to 2 hours - AS1905.1:2005
- Pairs back-to-back with the 203 Series interior plate (round corner)
- Compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches and push/pull doors
- 25-year mechanical warranty
Suitable Uses
- Push/pull pass doors in commercial, retail, hospitality and public-access buildings
- High-traffic entry and internal doors requiring clear pull-side directional signage
- Applications where no keyed access or locking function is needed on the exterior face
- Fire-rated door assemblies (when paired with a rated Lockwood mortice lock)
- Architecturally specified projects requiring engraved wayfinding in a round corner stainless steel plate
Full Specifications
Item Codes
Dimensions & Technical Drawings
Helpful Tips
- Exterior plate - pairs with 203 Series: This is the outside face plate. It must be paired with a 203 Series interior plate (round corner) - not a 201 Series (square corner).
- Full infill vs outlined engraving: This plate uses full solid infill engraving (code X) - the "PULL" text is filled with solid black gloss. If an outlined infill version is preferred, specify engraving code G instead. Both use black gloss infill as standard.
- Pairing with a Push plate: This plate is the pull-side of a push/pull door set. The interior or push-side plate should carry "PUSH" engraving - confirm the correct interior 203 Series variant is ordered to complete the set.
- No cylinder or locking function: This plate has no cylinder hole or turn snib. It is a pull-only plate - if keyed access from the exterior is required, refer to the cylinder pull handle variant (20225NA/P1).
- Concealed fixings: This plate uses concealed fixing studs. The paired interior 203 plate must use visible fixings - confirm this when ordering the interior plate.
- Handing: Determined by which side the hinges are on when facing the door from outside. Left hand = hinges on the left.
- 202 vs 200 Series: The 202 Series has 10mm radius round corners. If square corners are required, refer to the equivalent 200 Series plate.
- Thick doors: For doors 45-55mm, order long fixing screws SP2000-208 separately.
- Non-returnable: This item cannot be returned once ordered - confirm handing and suitability before purchasing.
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
- Mechanical components: 25 years
- Electrical and electronic components: 2 years (excluding batteries)
- Everbrass: 25 years
- Stainless Steel, Chrome & Anodised: Up to 10 years
- PVD / VIVID: 10 years
- Symmetry: 5 years
- Decorative finishes (Bronze, Antique, Powdercoat): Typically 2 years
Lockwood 200/202 Series Handle Catalogue
Lockwood Warranty
Lockwood branded products are covered by manufacturer warranties issued by ASSA ABLOY Australia Pty Ltd. Warranty periods vary by product type, with separate cover for mechanical components, electrical and electronic parts, keys, and finishes.
The summary below sets out the standard warranty structure. All warranty claims are handled by Terry's Tradies Pty Ltd and its associated websites, trading names, and subsidiaries. Full terms and exclusions are set out in the official Lockwood warranty document linked at the base of this page.
Warranty Summary
Finish Coverage Guide
- Everbrass finishes: up to 25 years against corrosion, tarnishing and discolouration.
- Stainless steel, polished stainless steel, chrome plating and anodised finishes: typically up to 10 years.
- PVD and VIVID finishes: typically up to 10 years.
- Symmetry range finishes: typically up to 5 years.
- Decorative finishes (Antique Copper, Architectural Bronze, Oil Rubbed Bronze, Aged Brass, Polished Brass, Satin Brass and related variants): typically up to 2 years against corrosion.
- Unlacquered brass finishes naturally age and change appearance over time. This is not considered a defect.
- Tea staining of stainless steel is not covered where the required cleaning and maintenance have not been followed.
How to Make a Claim
- Contact Terry's Tradies Pty Ltd and its associated websites, trading names, and subsidiaries with your proof of original purchase.
- Keep the product securely packed and clearly identified, ready for assessment.
- Where a claim is escalated to the manufacturer, ASSA ABLOY may issue a case number before goods are returned.
- ASSA ABLOY assesses the claim and determines repair, replacement with the same or closest equivalent product, or refund of the purchase price.
Exclusions
- Normal wear and tear.
- Misuse, abuse, accidental damage or use outside published specifications.
- Improper maintenance or failure to follow care instructions.
- Unauthorised modification, repair or use of non-genuine parts.
- Exposure to corrosive environments including coastal air, salt spray, chemicals or pollution.
- Removal, refitment or associated labour charges.
- Products not originally sold in Australia through authorised channels.
These manufacturer warranties apply in addition to your rights under the Australian Consumer Law. Our goods come with guarantees that cannot be excluded under the ACL. You are entitled to a replacement or refund for a major failure and to compensation for any other reasonably foreseeable loss or damage. Where a failure does not amount to a major failure, you are entitled to have the goods repaired or replaced.
