Lockwood 202 Exterior Round Corner Plate - Pull Outlined Engraving & P1 Pull Handle | Satin Stainless Steel
The Lockwood 202 Series Exterior Plate with Pull Outlined Engraving and P1 Pull Handle is part of the distinguished Artefact range of round corner plate door furniture - designed, assembled and customised in Australia for the Australian market. This exterior plate features a P1 stainless steel pull handle alongside an outlined "PULL" text engraving (black gloss, hollow letter style), providing clear pull-side directional instruction for building occupants on push/pull pass doors.
The outlined infill engraving (code G) produces a refined, outlined letter appearance - the "PULL" text is engraved with a black gloss outline rather than a fully solid fill, giving a lighter visual style compared to the solid infill variant. No cylinder or turn snib is included - this is a pull-only exterior plate suited to commercial, retail, hospitality and public-access pass doors. The plate pairs back-to-back with the 203 Series interior plate (round corner) and is compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches and push/pull doors.
The 202 Series features the same 162 x 162mm plate profile as the 200 Series but with 10mm radius corners. Supplied in Satin Stainless Steel in both left and right hand.
Usually ships in 11 business days
This product is a special order item and cannot be returned. Please confirm handing and suitability before ordering.
Finish
Satin Stainless Steel
SS
Available in left and right hand. Single finish option for this configuration.
Fire Rated
- Tested up to 2 hours with a fire rated Lockwood mortice lock on fire door assemblies in accordance with AS1905.1:2005 (Fire Resistant Doorsets).
- Fire performance is dependent on doorset type and configuration.
- Fire compliance is system-based and limited by the Fire Resistance Level of the complete doorset assembly.
Key Features
- Round corner 162 x 162mm exterior plate with 10mm radius corners - Lockwood Artefact 202 Series
- Pull Handle Only configuration (Function 24) with outlined "PULL" text engraving
- P1 stainless steel pull handle on exterior face
- Outlined infill "PULL" engraving (code G) - black gloss hollow letter style
- No cylinder or turn snib - pull-only exterior plate
- Concealed fixings - clean exterior face with no visible screws
- Available in left and right hand
- Designed, assembled and customised in Australia for the Australian market
- Tested to Level D8 (500,000 cycles) - AS4145.2-2008
- Fire rated up to 2 hours - AS1905.1:2005
- Pairs back-to-back with the 203 Series interior plate (round corner)
- Compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches and push/pull doors
- 25-year mechanical warranty
Suitable Uses
- Push/pull pass doors in commercial, retail, hospitality and public-access buildings
- High-traffic entry and internal doors requiring clear pull-side directional signage with a refined outlined engraving aesthetic
- Applications where no keyed access or locking function is needed on the exterior face
- Fire-rated door assemblies (when paired with a rated Lockwood mortice lock)
- Architecturally specified projects requiring engraved wayfinding on a round corner stainless steel plate
Full Specifications
Item Codes
Dimensions & Technical Drawings
Helpful Tips
- Outlined vs solid infill engraving: This plate uses outlined infill (code G) - the "PULL" letters have a black gloss outline with the interior of the letters not filled. For a fully solid black gloss "PULL" text, specify the full infill variant (code X, item code prefix 20224XN/P1). Both styles use black gloss as standard.
- Exterior plate - pairs with 203 Series: This is the outside face plate. It must be paired with a 203 Series interior plate (round corner) - not a 201 Series (square corner). The interior plate for a push/pull door should carry "PUSH" engraving on the inside face.
- No cylinder or locking function: This plate has no cylinder hole. If keyed exterior access is also required on the same plate, refer to the cylinder pull handle variant (20225NA/P1).
- Concealed fixings: This plate uses concealed fixing studs. The paired interior 203 plate must use visible fixings - confirm this when ordering the interior plate.
- Handing: Determined by which side the hinges are on when facing the door from outside. Left hand = hinges on the left.
- 202 vs 200 Series: The 202 Series has 10mm radius round corners. For the same plate in square corners, refer to the equivalent 200 Series plate.
- Thick doors: For doors 45-55mm, order long fixing screws SP2000-208 separately.
- Non-returnable: This item cannot be returned once ordered - confirm handing and suitability before purchasing.
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
- Mechanical components: 25 years
- Electrical and electronic components: 2 years (excluding batteries)
- Everbrass: 25 years
- Stainless Steel, Chrome & Anodised: Up to 10 years
- PVD / VIVID: 10 years
- Symmetry: 5 years
- Decorative finishes (Bronze, Antique, Powdercoat): Typically 2 years
Lockwood 200/202 Series Handle Catalogue
Lockwood Warranty
Lockwood branded products are covered by manufacturer warranties issued by ASSA ABLOY Australia Pty Ltd. Warranty periods vary by product type, with separate cover for mechanical components, electrical and electronic parts, keys, and finishes.
The summary below sets out the standard warranty structure. All warranty claims are handled by Terry's Tradies Pty Ltd and its associated websites, trading names, and subsidiaries. Full terms and exclusions are set out in the official Lockwood warranty document linked at the base of this page.
Warranty Summary
Finish Coverage Guide
- Everbrass finishes: up to 25 years against corrosion, tarnishing and discolouration.
- Stainless steel, polished stainless steel, chrome plating and anodised finishes: typically up to 10 years.
- PVD and VIVID finishes: typically up to 10 years.
- Symmetry range finishes: typically up to 5 years.
- Decorative finishes (Antique Copper, Architectural Bronze, Oil Rubbed Bronze, Aged Brass, Polished Brass, Satin Brass and related variants): typically up to 2 years against corrosion.
- Unlacquered brass finishes naturally age and change appearance over time. This is not considered a defect.
- Tea staining of stainless steel is not covered where the required cleaning and maintenance have not been followed.
How to Make a Claim
- Contact Terry's Tradies Pty Ltd and its associated websites, trading names, and subsidiaries with your proof of original purchase.
- Keep the product securely packed and clearly identified, ready for assessment.
- Where a claim is escalated to the manufacturer, ASSA ABLOY may issue a case number before goods are returned.
- ASSA ABLOY assesses the claim and determines repair, replacement with the same or closest equivalent product, or refund of the purchase price.
Exclusions
- Normal wear and tear.
- Misuse, abuse, accidental damage or use outside published specifications.
- Improper maintenance or failure to follow care instructions.
- Unauthorised modification, repair or use of non-genuine parts.
- Exposure to corrosive environments including coastal air, salt spray, chemicals or pollution.
- Removal, refitment or associated labour charges.
- Products not originally sold in Australia through authorised channels.
These manufacturer warranties apply in addition to your rights under the Australian Consumer Law. Our goods come with guarantees that cannot be excluded under the ACL. You are entitled to a replacement or refund for a major failure and to compensation for any other reasonably foreseeable loss or damage. Where a failure does not amount to a major failure, you are entitled to have the goods repaired or replaced.
