Lockwood 215VISPPSS Push/Pull Plate Full Set Visible Fix 300 x 100mm – Satin Stainless Steel (Box of 10)
The Lockwood 215VISPPSS is a trade pack supplying ten complete push/pull plate full sets in satin stainless steel. Each full set is a visible-fix configuration from the Lockwood 214/215 Series and is designed for back-to-back installation through the door.
Each plate measures 300mm x 100mm x 2mm with 10mm radius corners. Visible fix plates feature countersunk fixing holes and are fixed back to back through the door using the matched exterior and interior plates.
This trade pack is intended for projects, contractors and locksmiths fitting out multiple doors in public, commercial, industrial and institutional buildings. The 214/215 Series is designed for use with Lockwood 3570 Synergy Series and 3770 Selector Series mortice locks.
Estimated Warehouse Dispatch
Usually ships in 2 business days
Usually ships in 2 business days
Trade Pack – Box of 10 Full Sets
Supplied as a bulk trade pack of ten complete push/pull plate full sets for multi-door projects.
Supplied as a bulk trade pack of ten complete push/pull plate full sets for multi-door projects.
Available Finish
Satin Stainless Steel
This trade pack is supplied in satin stainless steel. The 214/215 Series is also available in other finishes as separate SKUs.
Fire Rated
- Successfully tested up to 4 hours on fire door assemblies in accordance with Australian Standard AS1905.1-2005 Part 1: Fire Resistant Doorsets.
- Fire performance applies only when installed as part of an approved fire-rated doorset assembly.
- Fire compliance is system-based and is limited by the Fire Resistance Level of the complete doorset.
Disability Act Compliance (DDA)
- Compliant with Australian Standard AS1428.1 for disabled access.
- Compliance applies to the pull handle design when installed correctly on the plate.
Key Features
- Trade pack of ten complete push/pull plate full sets.
- Visible fix plate construction with countersunk fixing holes.
- Back-to-back installation through the door.
- 300mm x 100mm x 2mm plates with 10mm radius corners.
- Satin stainless steel finish across all plates in the pack.
- Designed for use with Lockwood 3570 Synergy and 3770 Selector Series mortice locks.
- Suitable for high-traffic public, commercial, industrial and institutional buildings.
- Pull handle design complies with AS1428.1 disabled access requirements.
- Fire tested to AS1905.1-2005 Part 1 up to 4 hours on approved doorsets.
- Backed by Lockwood 25 Year Mechanical Warranty.
Suitable Uses
- Multi-door project fit-outs
- Public buildings and civic facilities
- Commercial office buildings
- Industrial facilities
- Institutional buildings including schools and hospitals
- High-traffic internal and external commercial doors
- Fire-rated doorset assemblies
- Applications requiring DDA-compliant pull handles
Full Specifications
Frequently Asked Questions
- What is included in this trade pack?
This SKU is supplied as a box of ten complete push/pull plate full sets. Each full set is a visible-fix configuration from the 214/215 Series in satin stainless steel. Buyers should confirm the specific plate function and handle configuration with their Gold Coast Hardware sales contact prior to ordering for a critical project. - What does visible fix mean?
Visible fix plates have countersunk fixing holes on the face of the plate and are fixed back to back through the door. The fixing screws are visible from the face of the plate after installation. - Does this pack include fixing screws?
Standard plates are fixed back to back through the door. For doors 45mm to 55mm thick, long fixing screws SP2000-208 are required and must be ordered separately. - Is this pack handed?
The 214/215 Series plates are generally non-handed for standard pull functions. Where a plate function includes a cylinder, turn snib or handed feature, handing must be confirmed prior to ordering. - Can these plates be used on fire doors?
Yes, when installed as part of an approved fire-rated doorset. The 214/215 Series has been tested to AS1905.1-2005 Part 1 for up to 4 hours. Fire compliance depends on the complete doorset assembly.
Additional Information
- Trade Pack Format:
This SKU is a bulk trade pack. Where individual plates are required, refer to the standard Lockwood 2000 Series single-unit SKUs (for example 21400NA, 21500NA and function-specific variants) which are sold separately. - Back-to-Back Installation:
Visible fix plates are designed to be installed in matched pairs (exterior plate paired with interior plate) with fixing screws running back to back through the door. - Thicker Doors:
Standard fixings suit doors 35mm to 45mm thick. For doors between 45mm and 55mm, long fixing screws (part SP2000-208) must be specified at time of ordering. - Fire Door Applications:
Fire performance is achieved only when the complete doorset (door leaf, frame, hardware and seals) is assembled in accordance with the tested configuration. The plate itself cannot provide a fire rating in isolation. - Mortice Lock Compatibility:
The 214/215 Series is designed for use with Lockwood 3570 Synergy Series and 3770 Selector Series mortice locks. Other mortice locks should be confirmed for compatibility prior to installation. - Confirm Configuration Before Ordering:
Plate function (cylinder hole, turn snib, emergency turn, engraving and handle length) can vary across the 214/215 range. Buyers specifying for a critical project should confirm the exact plate configuration contained in this trade pack with a Gold Coast Hardware sales contact before placing a bulk order. - Maintenance:
Clean with a soft cloth and mild detergent. Avoid abrasive cleaners, acidic cleaners and scouring pads which may damage the satin stainless steel finish.
Lockwood Warranty (Australia)
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
- Mechanical components: 25 years
- Electrical and electronic components: 2 years (excluding batteries)
Cosmetic finishes, batteries, normal wear and tear, misuse, unauthorised modification, corrosion and labour or freight costs are excluded.
This warranty operates in addition to rights available under the Australian Consumer Law.
Download PDF Resources
Lockwood Push/Pull Door Handles Catalogue
Lockwood Push/Pull Door Handles Catalogue
Download PDF Resources
Lockwood Push/Pull Door Handles Catalogue
Lockwood Push/Pull Door Handles Catalogue
Lockwood Warranty Overview
Lockwood branded products are covered by manufacturer warranties issued by ASSA ABLOY Australia Pty Ltd. Warranty periods vary depending on product type, mechanical components, electrical elements, and finish category.
This overview summarises the structure of Lockwood warranty coverage. Full terms, exclusions and claim procedures are set out in the official Lockwood Warranty document.
Warranty Periods Summary
Finish Coverage Guide
- Everbrass finishes: up to 25 years against corrosion, tarnishing and discolouration.
- Stainless steel, polished stainless steel, chrome plating and anodised finishes: typically up to 10 years.
- Decorative finishes including Antique Copper, Architectural Bronze, Oil Rubbed Bronze, Aged Brass, Polished Brass, Satin Brass and related variants: typically up to 2 years against corrosion.
- Unlacquered brass finishes will naturally age and change appearance over time. This is not considered a defect.
- Tea staining of stainless steel is not covered where cleaning and maintenance have not been followed.
What the Warranty Covers
- Defects in material and workmanship during the applicable warranty period.
- Assessment by ASSA ABLOY to determine repair, replacement with the same or closest equivalent product, or refund of purchase price.
Common Exclusions
- Normal wear and tear.
- Misuse, abuse, accidental damage or use outside published specifications.
- Improper maintenance or failure to follow care instructions.
- Unauthorised modification, repair or use of non-genuine parts.
- Exposure to corrosive environments including coastal air, salt spray, chemicals or pollution.
- Removal, refitment or associated labour charges.
- Products not originally sold in Australia through authorised channels.
Warranty Claim Process
- Retain proof of original purchase.
- Return the product through the original place of purchase where applicable.
- If claiming directly, obtain a case number before returning goods.
- Products must be securely packed and clearly identified.
- Warranty assessment determines repair, replacement or refund.
Australian Consumer Law
Lockwood warranties operate in addition to rights available under the Australian Consumer Law. Goods come with guarantees that cannot be excluded. Customers may be entitled to a replacement or refund for a major failure and compensation for reasonably foreseeable loss or damage.
Where a product fails to meet acceptable quality standards and the failure does not amount to a major failure, the customer is entitled to repair or replacement.
