Lockwood 201 Interior Square Corner Plate – Lever 96 | Artefact Series
The Lockwood 201 Series Interior Plate with Lever 96 is part of the premium Artefact range of square corner plate door furniture — designed, assembled and customised in Australia for the Australian market. This configuration features a lever-only interior plate (no cylinder, no turnknob), making it the ideal inside plate for passage and push/pull door applications where free, unimpeded egress is required from the interior side.
The 201 plate pairs back-to-back with the 200 Series exterior plate, sharing the same 162 × 162mm square corner profile. It is compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks, latches, and push/pull doors.
Lever 96 is fully compliant with AS1428.1-2009 (Design for Access and Mobility), making this plate suitable for DDA-compliant installations. A broad range of finishes is available including the warm tones of Satin Brass and Oil Rubbed Bronze, through to the durability of 316 Marine Grade stainless steel.
Usually ships in 11 business days
This product is a special order item. Please confirm finish, handing and door thickness suitability before ordering as it cannot be returned.
Available Finish Options
316 Marine Grade
MG
Natural Anodised
NT
Oil Rubbed Bronze
ORB
Polished Stainless Steel
PS
Satin Brass
SB — Right Hand only-
Satin Stainless Steel
SS
Finish selection does not affect functionality, compliance, or performance. Oil Rubbed Bronze and Satin Brass are decorative finishes — refer to the finish warranty guide below for applicable coverage.
Fire Rated
- Tested up to 4 hours with a fire rated Lockwood mortice lock on fire door assemblies in accordance with AS1905.1:2005 (Fire Resistant Doorsets).
- Fire performance is dependent on doorset type and configuration.
- Fire compliance is system-based and limited by the Fire Resistance Level of the complete doorset assembly.
Disability Act Compliance (DDA)
- Lever 96 meets the requirements of AS1428.1-2009, Design for Access and Mobility.
- Suitable for applications requiring DDA-compliant door hardware under the BCA.
- Lever compliance relates to handle design only and does not imply full building compliance.
Key Features
- Square corner 162 × 162mm interior plate — Lockwood Artefact Series
- Lever-only configuration (Function 05) — no cylinder or turnknob
- Provides free, unimpeded egress from the interior side at all times
- Designed, assembled and customised in Australia for the Australian market
- Lever 96 is AS1428.1-2009 compliant — suitable for DDA / accessible design installations
- Tested to Level D8 (500,000 cycles) — AS4145.2-2008
- Fire tested up to 4 hours — AS1905.1:2005
- Pairs back-to-back with the 200 Series exterior plate
- Concealed or visible fixing options
- Available in left and right hand across a broad range of finishes
- Compatible with Lockwood Selector 3770 and Synergy 3570 Series Mortice Locks and latches
- 25-year mechanical warranty
Suitable Uses
- Passage doors requiring free interior egress with lever operation
- Commercial office, corridor and amenity doors
- Fire-rated door assemblies (when paired with a rated Lockwood mortice lock)
- DDA / accessibility-compliant installations
- Coastal and marine environments (316 Marine Grade finish)
- Architecturally specified residential and commercial projects
Full Specifications
Dimensions & Technical Drawings
Item Codes
Helpful Tips
- Interior plate only: The 201 Series is always the inside plate — pair with a 200 Series exterior plate.
- Lever only — no locking function: This configuration provides free passage from the interior. If privacy or locking is needed on the inside, consider the turnknob & lever variant (Function 04).
- Handing: Determined by which side the hinges are on when facing the door from outside. Left hand = hinges on the left.
- Satin Brass: Available in Right Hand only — confirm handing before ordering.
- Thick doors: For doors 45–55mm, order long fixing screws SP2000-208 separately.
- Fixing: If the outside plate is concealed fixed, the inside plate must be visible fixed.
- Decorative finishes: Oil Rubbed Bronze and Satin Brass carry a shorter finish warranty than stainless or anodised — refer to the finish warranty guide below.
- Non-returnable: Confirm all selections before ordering — this item cannot be returned once purchased.
Lockwood branded products purchased new in Australia from authorised resellers are covered against defects in materials and workmanship for:
- Mechanical components: 25 years
- Electrical and electronic components: 2 years (excluding batteries)
- Everbrass: 25 years
- Stainless Steel, Chrome & Anodised: Up to 10 years
- PVD / VIVID: 10 years
- Symmetry: 5 years
- Decorative finishes (Bronze, Antique, Powdercoat): Typically 2 years
Lockwood 200/202 Series Handle Catalogue
Lockwood Warranty Overview
Lockwood branded products are covered by manufacturer warranties issued by ASSA ABLOY Australia Pty Ltd. Warranty periods vary depending on product type, mechanical components, electrical elements, and finish category.
This overview summarises the structure of Lockwood warranty coverage. Full terms, exclusions and claim procedures are set out in the official Lockwood Warranty document.
Warranty Periods Summary
Finish Coverage Guide
- Everbrass finishes: up to 25 years against corrosion, tarnishing and discolouration.
- Stainless steel, polished stainless steel, chrome plating and anodised finishes: typically up to 10 years.
- Decorative finishes including Antique Copper, Architectural Bronze, Oil Rubbed Bronze, Aged Brass, Polished Brass, Satin Brass and related variants: typically up to 2 years against corrosion.
- Unlacquered brass finishes will naturally age and change appearance over time. This is not considered a defect.
- Tea staining of stainless steel is not covered where cleaning and maintenance have not been followed.
What the Warranty Covers
- Defects in material and workmanship during the applicable warranty period.
- Assessment by ASSA ABLOY to determine repair, replacement with the same or closest equivalent product, or refund of purchase price.
Common Exclusions
- Normal wear and tear.
- Misuse, abuse, accidental damage or use outside published specifications.
- Improper maintenance or failure to follow care instructions.
- Unauthorised modification, repair or use of non-genuine parts.
- Exposure to corrosive environments including coastal air, salt spray, chemicals or pollution.
- Removal, refitment or associated labour charges.
- Products not originally sold in Australia through authorised channels.
Warranty Claim Process
- Retain proof of original purchase.
- Return the product through the original place of purchase where applicable.
- If claiming directly, obtain a case number before returning goods.
- Products must be securely packed and clearly identified.
- Warranty assessment determines repair, replacement or refund.
Australian Consumer Law
Lockwood warranties operate in addition to rights available under the Australian Consumer Law. Goods come with guarantees that cannot be excluded. Customers may be entitled to a replacement or refund for a major failure and compensation for reasonably foreseeable loss or damage.
Where a product fails to meet acceptable quality standards and the failure does not amount to a major failure, the customer is entitled to repair or replacement.
